Samson 12-STRAND Class I Whoopie Sling Modified for Tenex Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Samson 12-STRAND Class I Whoopie Sling Modified for Tenex. Samson 12-STRAND Class I Whoopie Sling Modified for Tenex and Tenex-TEC User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
PAGE 1 OF 2
SamsonRope.com | Email [email protected] | Tel +1.360.384.4669
12-Strand Class I Whoopie Sling Modified for Tenex and Tenex-TEC
SAMSON SPLICING INSTRUCTIONS
1
step
Using these measurements do the Locked
Brummel Splice. Directions are as follows:
SPLICING FIXED EYE
These instructions are intended for use with Samson’s Tenex and Tenex-TEC (two-end per carrier Tenex) only. Published Whoopie Sling strengths are
for Samson’s Tenex-TEC when spliced in accordance with these instructions.
Note:
For longer sling lengths, determine length needed beyond the maximum length listed in the table to the right. Multiply the length needed by two and
add resulting amount to cut length. For example: If you need a maximum length of 8 ft. on a 3/4 inch sling, this is 2 ft. longer than the listed max length.
Multiply 2 ft. x 2 = 4 ft. Add this to the original cut length (4 ft. + 15 ft. = 19 ft.). Your cut length will need to be 28 ft. to make a sling that adjusts to 12 ft.
All slings use the
same measurements
with proper size fid.
1A
Leave tail at full volume.
Just cut end at an
angle, then tape.
CUT LENGTHS FOR SLINGS:
1/2" 10' 30" to 48"
5/8" 12' 36" to 60"
3/4" 15' 42" to 72"
Rope Cut Sling Adjusts
Size Length From/To
Mark A Mark B
1 fid 1 fid
1/2 fid
fid short section
1B
Pass taped end through
center of rope at Mark
B. Do not bury Mark A,
leave on entry side of
standing rope.
Mark A
Mark B
Mark A
Mark B
1 fid
Eye
1E
To bury the tail into the standing end, make a mark approximately 2 picks from where the standing
part passes through the tail (Mark C). This will be the tail entry point. From Mark C, measure down
the standing part 1 d length and make Mark D. Insert d and tapered tail at Mark C and bring out at
Mark D. Remove d and smooth the standing part out, which will bury the entire tail.
Mark D
1 fid
Mark C
(entry point)
1C
Pass the opposite
end through the
center of the tail
approximately
2 picks from
where it
exits the
standing rope.
1D
Close up
Brummel.
Pull
Pull
Pull
Pull
(Or desired
eye length)
Vue de la page 0
1 2

Résumé du contenu

Page 1 - SPLICING FIXED EYE

PAGE 1 OF 2SamsonRope.com | Email [email protected] | Tel +1.360.384.466912-Strand Class I Whoopie Sling Modified for Tenex and Tenex-TECSAMS

Page 2 - BACK SPLICING THE END

PAGE 2 OF 2SamsonRope.com | Email [email protected] | Tel +1.360.384.466912-Strand Class I Whoopie Sling Modified for Tenex and Tenex-TECSAMS

Commentaires sur ces manuels

Pas de commentaire