Samson DOUBLE BRAID Class I End-for-End Splice Manuel d'utilisateur télécharger pdf

PAGE 1 OF 4

SamsonRope.com | Email [email protected] | Tel +1.360.384.4669

Double Braid Class I End-For-End Splice

SAMSON SPLICING INSTRUCTIONS

Class I Double Braids are made from any or all of the following

bers: olen, polyester, or nylon.

This splice can be performed on new and used rope. This is an

all-purpose splice technique designed for people who generally

splice used rope as frequently as new rope.

MEASURING AND MARKING

step

EXTRACTING THE CORE

Bend rope sharply at Point X. With a pusher or any sharp tool, such as an ice pick, awl, or marlin spike, spread cover

strands to expose core. First pry, then pull core completely out of cover (shown in white) from Point X to the end of rope.

Put 1 layer only of tape on end of core (shown in gray.)

To assure correct positioning of Mark 1 do the following: holding the exposed core, slide cover as far back towards the

tightly tied slip knot as you can. Then, rmly smooth cover back from the slip knot towards taped end. Smooth again until

all cover slack is removed. Then, mark core where it comes out of cover. This is Mark 1. Do this to both ropes. (Fig. A)

Tape the end of each rope with 1 thin layer of tape. Lay 2 ropes to be spliced side-by-side and measure 1 tubular d length

(or 2 wire d lengths) from end of each rope and make a mark. This is Point R (Reference).

From Point R measure 1 short d section length (as scribed on the d) then mark. This is Point X (where you should extract

core from inside cover.) Be sure both ropes are identically marked. Tie a slipknot approximately 5 d lengths from Point X.

Note: If you require the rope

with the nished splice to

be a certain overall ength,

refer to “Special Tips for

Splicing Double Braid

Class I”, on th last page

of these splice instructions.

1 ﬁd OR

2 wire ﬁds

Core must be extracted

from cover here.

Tie a slipknot in each line about

5 ﬁd lengths from Point X.

Short

section

of ﬁd

1 layer of

tape

X R

Finished splice

One layer

of tape

cover

core

cover

Mark 1

Do not pull cover strands away from rope as this will distort cover unnecessarily.

Mark 3

1 ﬁd length plus another short section

Mark second core using ﬁrst as exact guide

cover

core

cover

Mark 2

Short section

Mark 1

From Mark 1, measure along

core towards X a distance

equal to the short section

of d and make 2 heavy

marks. This is Mark 2.

From Mark 2 measure in the

same direction 1 d length

plus another short section

and make 3 heavy marks.

This is Mark 3.

Mark second core by laying it alongside

the rst and using it as an exact guide.

Figure A

Figure B

step

INSERTING CORE INTO CORE

Hold 1 core at Mark 1 and slide cover back to expose more core. (Fig. B)

1 2 3 4

Résumé du contenu

Page 1 - INSERTING CORE INTO CORE

PAGE 1 OF 4SamsonRope.com | Email [email protected] | Tel +1.360.384.4669Double Braid Class I End-For-End SpliceSAMSON SPLICING INSTRUCTIONS

Page 2 - REPOSITIONING THE ROPES

PAGE 2 OF 4SamsonRope.com | Email [email protected] | Tel +1.360.384.4669Double Braid Class I End-For-End SpliceSAMSON SPLICING INSTRUCTIONS

Page 3 - FINISHING THE SPLICE

PAGE 3 OF 4SamsonRope.com | Email [email protected] | Tel +1.360.384.4669Double Braid Class I End-For-End SpliceSAMSON SPLICING INSTRUCTIONS

Page 4

PAGE 4 OF 4SamsonRope.com | Email [email protected] | Tel +1.360.384.4669Special Tips for Splicing Double Braid Class ISAMSON SPLICING INSTR

Commentaires sur ces manuels

Pas de commentaire

Samson DOUBLE BRAID Class I End-for-End Splice Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Samson DOUBLE BRAID Class I End-for-End Splice. Samson DOUBLE BRAID Class I End-for-End Splice User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Samson DOUBLE BRAID Class I End-for-End Splice