Samson DOUBLE BRAID Special Tips for Splicing Double Brai Manuel d'utilisateur télécharger pdf

DOCUMENT DblBrd_Special Tips_SEPT2012.pdf PAGE 1 OF 1

SamsonRope.com | Email [email protected] | Tel +1.360.384.4669

Special Tips: Splicing Double Braid Rope

SAMSON SPLICING INSTRUCTIONS

Splice With thimble

Follow Step 1 of the Eye Splice Double Braid Class I for determining the correct

eye size. When burying exposed core, as in Step 8, bury to crossover, then insert

thimble into eye before milking cover all the way. If using a thimble with ears, before

inserting cover into core, as in Step 5, insert core through the rings (dog ears) and

slide thimble beyond Mark 3. Proceed to make the splice according to instructions.

Note: Before nal burying, slide thimble around to cover side of eye. To secure

nished eye tightly around thimble, either whip throat or dip the eye in hot water

for several minutes. Hot water will shrink the eye tightly around thimble for nylon

and polyester ber ropes.

Splicing RopeS 3" diameteR oR laRgeR

Before splicing rope, measure back 8 ds and insert a large d through the rope to anchor the core and cover

together. Use a milking strap to milk slack of cover toward end of rope. A milking strap is a smaller diameter rope

that is cinched around the rope to create more seizing power than a human hand can apply. It helps to pull the

milking strap with mechanical means (a winch or come-along.) Cut off any excess cover.

Milking the cover is a crucial step and will be done several times during this splice. The milking

process aligns the core and cover braid angles and allows them to more effectively share

the load when the rope is in use. It is best done with a milking strap

for ropes 3" diameter or larger.

After milking, check for cover slack. If cover slack remains,

repeat milking process until slack is gone.

Minimum endless loop (Grommet) with Class I Double

Braid is 10 d lengths between extraction Mark X to

extraction Mark X, regardless of rope diameter.

end-FoR-end Splice

Exact overall lengths with endless loops are determined by

allowing for extra rope consumed in making the End-for-End

Splice. The length of extra rope is equal to 4 ﬁd lengths.

Example: To make an endless loop 10' overall:

10 Ft.

20 Ft.

4 ﬁds

Measure and cut a length:

minimum lengthS

Minimum eye-and-eye sling length with Class I

Double Braid is 5 d lengths from extraction Mark X

to extraction Mark X, regardless of rope diameter.

The size of eye does not affect the minimum length.

Example: How to make an Eye-and-Eye Sling

10' long overall with two 6" eyes:

Measure and cut a length:

10 ft.

1 Eye

Circ. 3 ﬁds

5 ﬁds

Mark X

Mark R

Mark X

Mark R

SAMSON SPLICING INSTRUCTIONS 1

Résumé du contenu

Page 1 - SAMSON SPLICING INSTRUCTIONS

Plus de documents pour Outils Samson DOUBLE BRAID Special Tips for Splicing Double Brai

Voir le document Samson DOUBLE BRAID Special Tips for Splicing Double Brai Manuel d'utilisateur

Samson DOUBLE BRAID Special Tips for Splicing Double Brai Manuel d'utilisateur (1 pages)

Commentaires sur ces manuels

Pas de commentaire

Samson DOUBLE BRAID Special Tips for Splicing Double Brai Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Samson DOUBLE BRAID Special Tips for Splicing Double Brai. Samson DOUBLE BRAID Special Tips for Splicing Double Braid User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Outils Samson DOUBLE BRAID Special Tips for Splicing Double Brai

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Samson DOUBLE BRAID Special Tips for Splicing Double Brai