Samson 1400 Instructions d'exploitation Page 76
- Page / 124
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
8.2.2 Fail-safe position (SAFE)
If you want to move the valve to fail-safe po
-
sition determined during start-up (see sec
-
tion 7.1), proceed as follows:
Turn
®
Code 0
Press , display: current operating mode
(
AUTO
or
MAN
), Code 0 blinks
Turn
®
SAFE
Press , display:
S
The valve moves to the fail-safe position.
Once the positioner is initialized, the current
valve position is indicated on the display in
%.
Exit the fail-safe position
Turn
®
Code 0
Press , Code 0 blinks
Turn and select the required operating
mode
AUTO
or
MAN
.
Press .
The positioner switches to the operating
mode selected.
8.3 Malfunction/Failure
All status and error messages are classified
according to a status in the positioner. The
default settings of the status classification are
listed in the code list.
Note: The status classification can only be
changed in the operator software, e.g.
TROVIS-VIEW 4. For more details, refer to
the Operating Instructions EB 8389-1 EN on
EXPERTplus Valve Diagnostics.
To provide a better overview, the classified
messages are summarized in a condensed
state. The following status messages are
available:
4
Failure
The positioner cannot perform its control
task due to a functional fault in the de-
vice or in one of its peripherals or an ini-
tialization has not yet been successfully
completed.
4
Maintenance required
The positioner still performs its control
task (with restrictions). A maintenance
requirement or above average wear has
been determined. The wear tolerance will
soon be exhausted or is reducing at a
faster rate than expected. Maintenance is
necessary in the medium term.
4
Maintenance demanded
The positioner still performs its control
task (with restrictions). A maintenance
demand or above average wear has
been determined. The wear tolerance will
soon be exhausted or is reducing at a
faster rate than expected. Maintenance is
necessary in the short term.
76 EB 8384-6 EN
Operation
- Mounting and 1
- Operating Instructions 1
- EB 8384-6 EN 1
- 2 EB 8384-6 EN 2
- EB 8384-6 EN 3 3
- EB 8384-6 EN 5 5
- (ATEX) and 89/336/EEC (EMC) 6
- 2 Article code 7
- 3 Design and principle of 8
- Fig. 2 · Functional diagram 9
- 3.1 Safety function (SIL) 10
- 3.2 Valve diagnostics 10
- 3.3 Flow rate calculation 10
- EB 8384-6 EN 11 11
- • Full scope of functions 11
- – Function is not performed 11
- 3.4 Type of application 12
- 3.5 Communication 12
- 3.5.1 Configuration using 12
- TROVIS-VIEW 4 12
- 3.6 Additional equipment 13
- 3.7 Technical data 15
- No response/No 16
- Response/Fault 16
- 18 EB 8384-6 EN 18
- EB 8384-6 EN 19 19
- 4 Attachment to the control 20
- Travel tables 21
- 4.1 Direct attachment 22
- 4.1.1 Type 3277-5 Actuator 22
- 4.1.2 Type 3277 Actuator 24
- 4.2 Attachment according to 26
- IEC 60534-6 (NAMUR) 26
- 4.3 Attachment to Type 3510 28
- Micro-flow Valve with 28
- Type 3271-5 Actuator 28
- 4.4 Attachment to rotary 30
- 4.4.1 Heavy-duty version 32
- 1.1, 1.2 14.1 3 14 99.1 36
- 2 1 1.1, 1.2 38
- 4.7 Mounting the leakage 39
- 4.9 Air purging function for 40
- 42 EB 8384-6 EN 42
- 44 EB 8384-6 EN 44
- 5 Connections 45
- 5.1 Pneumatic connections 45
- 5.1.1 Signal pressure gauges 45
- 5.1.2 Supply pressure 45
- 5.2 Electrical connections 46
- EB 8384-6 EN 47 47
- 5.2.1 Switching amplifiers 48
- Controller/control station 50
- EB 8384-6 EN 51 51
- 6 Operator controls and 52
- ACTUATES 53
- 6.1 Serial interface 54
- 6.2 HART 54
- 6.3 Dynamic HART 54
- EB 8384-6 EN 55 55
- 7 Start-up – Settings 56
- 7.1 Defining the valve closed 56
- MAX BACK 57
- MIN SIDE 57
- MIN BACK 57
- MAX SIDE 57
- 7.5 Checking the operating 58
- 7.6 Initialization 59
- Pin position 61
- EB 8384-6 EN 61 61
- OPEN position 62
- Enable configuration 65
- EB 8384-6 EN 65 65
- 7.7 Zero calibration 68
- EB 8384-6 EN 69 69
- 7.9 Reset to default values 71
- 72 EB 8384-6 EN 72
- Start-up – Settings 72
- 8 Operation 74
- 8.1 Enabling and selecting 74
- 8.2 Operating modes 75
- 8.2.1 Automatic and manual mo 75
- 8.3 Malfunction/Failure 76
- Example: 77
- Error caused by pin 77
- EB 8384-6 EN 77 77
- 9 Adjusting the limit switch 78
- EB 8384-6 EN 79 79
- 9.1 Retrofitting an inductive 80
- 10 Maintenance 81
- 11 Servicing 81
- 12 Firmware update (serial 81
- 13 Maintenance, calibration 82
- 14 Code list 83
- NOTICE If you select a pin 84
- 86 EB 8384-6 EN 86
- 88 EB 8384-6 EN 88
- The setting has no effect 90
- (Code 6) is selected 92
- 94 EB 8384-6 EN 94
- 96 EB 8384-6 EN 96
- 98 EB 8384-6 EN 98
- 100 EB 8384-6 EN 100
- Code list 100
- 102 EB 8384-6 EN 102
- Initialization errors 102
- Operational errors 104
- 104 EB 8384-6 EN 104
- Hardware errors 105
- Error appendix 106
- Data errors 106
- 106 EB 8384-6 EN 106
- Diagnostic errors 107
- 108 EB 8384-6 EN 108
- 15 Dimensions in mm 109
- 110 EB 8384-6 EN 110
- Dimensions in mm 110
- EB 8384-6 EN 111 111
- EB 8384-6 EN 113 113
- 114 EB 8384-6 EN 114
- EB 8384-6 EN 115 115
- 116 EB 8384-6 EN 116
- EB 8384-6 EN 117 117
- 118 EB 8384-6 EN 118
- EB 8384-6 EN 119 119
- 120 EB 8384-6 EN 120
- EB 8384-6 EN 121 121
- EB 8384-6 EN 123 123
Produits connexes et manuels pour Amplificateurs audio Samson 1400
(44 pages)
(80 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.131 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels