Samson 1400 Instructions d'exploitation Page 15
- Page / 100
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4 Attachment to the control
valve – Mounting parts and
accessories
WARNING!
Attach the positioner, keeping the following
sequence:
1. Mount the positioner on the control valve
2. Connect the supply air
3. Connect the electrical power
4. Perform the start-up settings
The positioner is suitable for the following
types of attachment:
4
Direct attachment to SAMSON
Type 3277 Actuator
4
Attachment to actuators according to
IEC 60534-6 (NAMUR)
4
Attachment to Type 3510 Micro-flow
Valve
4
Attachment to rotary actuators
NOTICE
Attach the positioner to the control valve,
observing the following instructions to avoid
damaging the positioner.
–
Use only the mounting parts/accessories
listed in the Tables 1 to 5 (pages 30 to
33) to mount the positioner. Observe the
type of attachment!
–
The positioner is fitted with pneumatic
connections with ¼ NPT threads. If you
need G ¼ threads, attach the connecting
plate (6) listed in the accessories.
–
Observe the assignment between lever
and pin position (see travel tables on
page 16).
–
Fit a signal pressure restriction (Table 5
on page 33) for actuators with di
-
aphragm areas smaller than 240 cm².
Lever and pin position
The positioner is adapted to the actuator
and to the rated travel by the lever on the
back of the positioner and the pin inserted
into the lever.
The travel tables on page 16 show the maxi
-
mum adjustment range at the positioner. The
travel that can be implemented at the valve
is additionally restricted by the selected
fail-safe position and the required compres-
sion of the actuator springs.
The positioner is standard equipped with the
lever M (pin position 35).
Note: If the standard mounted lever M is re
-
placed, the newly mounted lever must be
moved once all the way as far as it will go
in both directions to adapt it to the internal
measuring lever.
EB 8387-3 EN 15
Attachment to the control valve – Mounting parts and accessories
Fig. 3 · Lever M with pin position 35 (delivered state)
- Mounting and 1
- Operating Instructions 1
- EB 8387-3 EN 1
- EB 8387-3 EN 3 3
- Instructions EB 8389 EN 5
- Vent opening 6
- 2 Article code 7
- 3 Design and principle of 8
- 3.1 Additional equipment 9
- 3.2 Communication 10
- 3.2.1 Configuration using 10
- TROVIS-VIEW software 10
- EB 8387-3 EN 11 11
- 3.3 Technical data 12
- 14 EB 8387-3 EN 14
- 4 Attachment to the control 15
- 4.1 Direct attachment 17
- 4.1.1 Type 3277-5 Actuator 17
- 4.1.2 Type 3277 Actuator 20
- 4.2 Attachment according to 22
- IEC 60534-6 (NAMUR) 22
- 4.3 Attachment to Type 3510 24
- Micro-flow Valve 24
- 4.4 Attachment to rotary 26
- 4.5 Reversing amplifier for 28
- 4.5.1 Reversing amplifier 28
- (1079-1118 or 1079-1119) 28
- Output 38 Supply 9 29
- 32 EB 8387-3 EN 32
- Table 5 · General accessories 33
- 5 Connections 34
- 5.1 Pneumatic connections 34
- 5.1.1 Signal pressure gauges 35
- 5.1.2 Supply pressure 35
- 5.2 Electrical connections 36
- EB 8387-3 EN 37 37
- (lid unscrewed) 38
- Connections 39
- EB 8387-3 EN 41 41
- 6 Operator controls and 42
- 6.1 Rotary pushbutton 42
- 6.2 Serial interface 42
- 6.3 Readings on display 42
- EB 8387-3 EN 43 43
- 44 EB 8387-3 EN 44
- 6.4 HART 45
- 6.4.1 Dynamic HART 45
- Start-up – Settings 46
- 7.1 Adapting the display 47
- 7.3 Checking the operating 48
- 7.4 Allocating the closed 49
- 7.5 Positioner initialization 49
- 7.5.2 Initialization based on 52
- NOM nominal range 52
- 7.6 Zero calibration 58
- 7.7 Reset to default values 59
- 8 Operation 60
- 8.1 Enabling and selecting 60
- 8.2 Operating modes 61
- 8.2.1 Automatic (AUTO) and 61
- 8.3 Malfunction/maintenance 62
- Error caused by pin 63
- EB 8387-3 EN 63 63
- 9 Maintenance 64
- 10 Servicing explosion 64
- 11 Code list 65
- 66 EB 8387-3 EN 66
- Code list 66
- 68 EB 8387-3 EN 68
- 70 EB 8387-3 EN 70
- 72 EB 8387-3 EN 72
- 74 EB 8387-3 EN 74
- EB 8387-3 EN 75 75
- Initialization errors 76
- 76 EB 8387-3 EN 76
- Operational errors 78
- 78 EB 8387-3 EN 78
- Hardware errors 79
- 80 EB 8387-3 EN 80
- Data errors 81
- 82 EB 8387-3 EN 82
- Diagnosis errors 83
- 12 Dimensions in mm 84
- Dimensions in mm 85
- 86 EB 8387-3 EN 86
- 13 Appendix 87
- EB 8387-3 EN 89 89
- 90 EB 8387-3 EN 90
- EB 8387-3 EN 91 91
- 92 EB 8387-3 EN 92
- EB 8387-3 EN 93 93
- 94 EB 8387-3 EN 94
- EB 8387-3 EN 95 95
- 96 EB 8387-3 EN 96
- EB 8387-3 EN 97 97
- EB 8387-3 EN 99 99
Produits connexes et manuels pour Amplificateurs audio Samson 1400
(12 pages)
(14 pages)
(5 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.229 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels