Samson AirLine SYNTH Spécifications Page 1

WIRELESS GUITAR SYSTEM

1. Antennas (A and B) - The antenna mountings allow full rotation for optimum placement. In normal operation, both Antenna A (the antenna on the le

6: EDIT Control – This rotary encoder control knob/switch is used to control and set several menu functions and parameters displayed in the LCD dis

A: Antenna socket - D hole knockout for mounting the antennas to the rear panel using the optional rear antenna kit.B: DC input - Connect the su

1: ¼-inch Phone Plug - Insert this standard 1/4” plug into your electric guitar or electric bass. Note that the angling of the plug can be configur

section on page 15 in this manual for more information about antenna positioning.7: Battery cover - Pull back gently on this cover at the ribbing a

The basic procedure for setting up and using your AirLine Synth system takes only a few minutes:1. Remove all packing materials (save them in case

6. Make the physical cable connection between the AR300 output jack and an audio input of your amplifier or mixer. Leave your amplifier or mixer of

13. Temporarily turn down the level of your amplifier or mixer and turn off the power to your transmitter, leaving the AR300 receiver on. Then restor

AR300 OperationSetting a Group and Channel Manually The AR300 receiver contains 320 selectable channels for N and U band, and 71 selectable channels f

AR300 OperationOperating In FREE ModeYou can tune in an exact frequency using the AR300’s FREE mode. Once you are in FREE mode you can change the freq

WARNINGTO PREVENT FIRE OR SHOCK HAZARD. DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTE

SYSTEM SPECIFICATIONS Channels 320 channels 25kHz Step (N and U Bands) 71 channels 25kHz Step (E Band)Operating Frequency 639.025–647 MHz 798

TRANSMITTER (AG300) Oscillation Type Crystal-controlled PLL frequency systhesizedModulation Type FMAntenna 1/4 Wave Length Wire TypeInput Impedan

FCC Rules and RegulationsSamson wireless systems are type accepted under FCC rules parts 90, 74 and 15.Licensing of Samson equipment is the user’s re

We, Samson Technologies Corporation, located at 45 Gilpin Ave, Hauppauge, NY 11788 USA declare under our own responsibility that the Products:are in c

Samson Technologies Corp.45 Gilpin AvenueHauppauge, New York 11788-8816Phone: 1-800-3-SAMSON (1-800-372-6766)Fax: 631-784-2201 www.samsontech.com

ATTENTION: Pour éviter tout risque d’électrocution ou d’incendie, ne pas exposer cet appareil à la pluie ou à l’humidité. Pour éviter tout risque d’él

PRECAUCION: Para reducir el riesgo de incendios o descargas, no permita que este aparato quede expuesto a la lluvia o la humedad. Para reducir el ries

Copyright 2011, Samson Technologies Corp.v2.1Samson Technologies Corp.45 Gilpin AvenueHauppauge, New York 11788-8816Phone: 1-800-3-SAMSON (1-800-372-6

Table of ContentsIntroduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1QuickStart . . . . . . . . . . . . . . . . . . . . . . . . . .

1IntroductionWelcome to Samson AirLine Synth—the next generation of wireless systems! Wireless microphone and instrument systems were originally devel

If you’ve had some prior experience using wireless systems, these QuickStart instructions will get you up and running with your AirLine Synth UHF guit

QuickStart7. Now to set the channel, press and hold the EDIT control until the display shows the Group number with three asterisks. Next, the AR300